SKU:
MR44BC-EAO
BRAND:
Kunz
The features of UTV 44 Rough Cut Mower will surely leave you shocked because it is one amazing and powerful machine. It is one of the best machines that you can get if you are working on a land that has constantly changing terrain.
Read More
44″ rough cut model with a commercial grade twin cylinder electric start engine and manual clutch blade engagement. Works great behind an ATV for smaller average jobs or tight clearance conditions
44" Rough Cut Mower Features:
- 44″ Cutting Width
- 23 HP Briggs & Stratton Commercial Grade Twin Cylinder Engine
- Commercial Grade Deck Assembly
- 4 Tire Design
- Quick Single Crank Height Adjust System
- Height Adjustment Range From 2″ to 8″
- Manual Clutch Blade Engagement
- Conservative 2″ Diameter Sapling Rating
- Pull Directly Behind or Fully Offset to the Side of the Tow Vehicle.
Specification | |
| Class Mower | Rough Cut (Rear Discharge) |
| Engine Make | Briggs & Stratton |
| Engine Model | Commercial Turf OHV (Twin Cylinder with Cyclonic Air Filtration System) |
| Engine HP | 20 |
| Lubrication Method | Pressure with Filter (Low Oil Pressure Shut Off Included) |
| Electric Start (Battery not included) | Yes |
| Number of Mower Blades | 2-23" |
| Blade Tip Speed (ft/min) | 19,000 |
| Cutting Width | 44" |
| Cutting Height | 2.0" - 8.0" With Single Crank Assy. |
| ATV Tongue | Standard (Direct Behind or Full Offset to Either Side) |
| Blade Engagement Clutch | Manual |
| Deck Metal Thickness | 8 GA |
| Deck Top Plate Thickness | 7 GA Backed with 1/4" Plate at Blade Spindles |
| Weight | 530 lbs |
| Pneumatic Fixed Rear Tire - Note: Flat Proof Urethance Tire Upgrade Available | 15/600x6, 4 Ply Tubeless |
| Pneumatic Front Tires on Casters - Note: Flat Proof Urethance Tire Upgrade Available | 5.30/4.50x6, 4 Ply Tubeless |
| Fuel Tank Size | 3 Gal. |
| Blade Spindles | |
| Shaft Size | 30mm |
| Bearing # | 6206-2RST |
| Drive Method | 1 B Section "V" Belt |
| Warranty | 1 Year Commercial (Engine - 3 Year Commercial) |
The Wetlands Kit consists of an extra set of tires and mounting brackets
- Great for wetlands or marshy areas that stay wet all year around
- Works well in combination with small personal amphibious vehicles
- Kit more than doubles the tire surface area in contact with the ground
- Easy to install
- Works on all existing and new rough cut mowers
- The rough cut mower will not float with the wetlands kit installed. Water greater than 2-3" in depth should be avoided.
- With the Wetlands Kit installed the minimum cutting height is 3.5"-4".
The Electric Lift Kit consists of all of the mounting hardware, brackets, electric actuator and wiring with remote control panel.
- Great for constantly changing terrain and grass/brush heights
- Allows for quick cutting height changes on the go from the seat of the tow vehicle
- Raise up and over rocks and logs with ease
- Heavy duty 1500 lb linear screw actuator made by Linak
- Works on all existing and new rough cut mowers
The Floatation Kit consists of one additional front and rear tire, mounting brackets and hardware
- Great for mowing around ponds and on rough uneven ground where scalping would normally occur
- Clamping style receiver allows for adjustments from side to side with both the front and rear tires
- Pinned receivers make for quick kit removal when not needed
- Works on all existing and new rough cut mowers
